SILICA REFRACTORIES FOR LINING OF OPEN-HEARTH GLASS FURNACE ACCORDING TO SPECIFICATION OF UKRAINE 23.2-00191738-011:2018

DS

DS

Products are intended for open-hearth glass furnace top structure laying.

DS grade is recommended for laying of less critical sections of open-hearth glass furnace with maximal operating temperature up to 1530°С. 
The products have high fire resistance and good resistance to corrosion due to volatile components of glass mix furnace-charge.

The products are also applied for laying of walls and arch of open-hearth glass furnace regenerators.

The products are supplied on wooden pallets interlaid with cardboard, with protected corners, wrapped with stretch film and bundled with plastic strip.
Parameter descriptionValue
Typesiliciferous
Groupsilica (SiO2 > 93%)
Refractoriness valuefire resistance (1580 to 1770°С)
Porosity degreeaverage dense (Ptot 20-30%)
Heat treatment methodburnt
Molding processsemidry forming
Binding type 1with inorganic binders
Binding type 2ceramic
Intended purposerepair/construction
Reference document for product propertiesSilica refractories for lining of open-hearth glass furnace according to Specification of Ukraine 23.2-00191738-011:2018
Reference documents for product dimensionsSilica refractories for lining of open-hearth glass furnace according to Specification of Ukraine 23.2-00191738-011:2018
Parameter descriptionValue
Apparent specific gravity, g/сm31,90
CaO, %≤3,0
Compression ultimate strength, N/mm2, not less than20,0
Density, g/сm3≤2,38
Fe2O3, %≤1,7
Fire resistance, °С, not less than1710
Fusion point, °С, not less than1640
Interconnected porosity, %, not more than22
SiO2, %≥94
FormArticle No.Additional informationPhoto
depending on drawingcustomer drawingUNDEFmark-11-conf-307-small.jpg
straight barNo.1for lining of walls and skew protectionmark-11-conf-311-small.jpg
No.10for laying of arches with thickness 500mm in combination with products No.27 and 28
No.2for pot opening foot bearing and skew protection
No.3for pot opening foot bearing
No.4for laying of arches with thickness 300mm in combination with product No.14
No.5for laying of arches with thickness 300mm in combination with products No.17 and No.18
No.7for laying of arches with thickness 400mm in combination with products No.21 and No.22
No.8for laying of arches with thickness 400mm in combination with products No.23 and No.24
No.9for laying of arches with thickness 500mm in combination with products No.25 and 26
V-shaped double-sided barNo.11for laying of arches, burners, ports and wall archesmark-11-conf-312-small.jpg
No.12for laying of arches of regenerators bonded with product No.15
No.13for laying of arches of regenerators bonded with product No.16
No.14for laying of arches with thickness 300mm in combination with product No.4
No.15for laying of arches of regenerators with thickness 300mm bonded with product No.12
No.16for laying of arches of regenerators bonded with product No.13
No.17for laying of arches with thickness 300mm in combination with product No.5
No.18for laying of arches with thickness 300mm in combination with product No.5
No.19for laying of arches with thickness 300mm in combination with product No.6
No.20for laying of arches with thickness 300mm in combination with product No.6
No.21for laying of arches with thickness 400mm in combination with product No.7
No.22for laying of arches with thickness 400mm in combination with product No.7
No.23for laying of arches with thickness 400mm in combination with product No.8
No.24for laying of arches with thickness 400mm in combination with product No.8
No.25for laying of arches with thickness 500mm in combination with product No.9
No.26for laying of arches with thickness 500mm in combination with product No.9
No.27for laying of arches with thickness 500mm in combination with product No.10
No.28for laying of arches with thickness 500mm in combination with product No.10
No.29for lining of flat arches bonded with product No.30
No.30for lining of flat arches bonded with product No.29
toothNo.31for lining of suspended wallsmark-11-conf-313-small.jpg
No.32for lining of suspended walls
left herringbone toothNo.34for lining of suspended wall cornersmark-11-conf-314-small.jpg
flat arch shoeNo.37for lining of flat archesmark-11-conf-315-small.jpg
right herringbone toothNo.33for lining of suspended wall cornersmark-11-conf-326-small.jpg
skewNo.35for laying of arches of burnersmark-11-conf-327-small.jpg
No.36for laying of arches of burners and ports
No.38for laying of arches with thickness 300mm
No.39for laying of arches with thickness 400mm
No.40for laying of arches with thickness 500mm
straight skewNo.41for laying of arches of drawing endsmark-11-conf-328-small.jpg
feather-edged skewNo.42for laying of arches of drawing endsmark-11-conf-329-small.jpg
FormArticle No.Dimension, mmDrawing
depending on drawingcustomer drawing
straight barNo.1UNDEFstraight bar
No.10UNDEF
No.2UNDEF
No.3UNDEF
No.4UNDEF
No.5UNDEF
No.7UNDEF
No.8UNDEF
No.9UNDEF
V-shaped double-sided barNo.11UNDEFV-shaped double-sided bar
No.12UNDEF
No.13UNDEF
No.14UNDEF
No.15UNDEF
No.16UNDEF
No.17UNDEF
No.18UNDEF
No.19UNDEF
No.20UNDEF
No.21UNDEF
No.22UNDEF
No.23UNDEF
No.24UNDEF
No.25UNDEF
No.26UNDEF
No.27UNDEF
No.28UNDEF
No.29UNDEF
No.30UNDEF
toothNo.31UNDEFtooth
No.32UNDEF
left herringbone toothNo.34left herringbone tooth
flat arch shoeNo.37flat arch shoe
right herringbone toothNo.33right herringbone tooth
skewNo.35UNDEFskew
No.36UNDEF
No.38UNDEF
No.39UNDEF
No.40UNDEF
straight skewNo.41UNDEFstraight skew
feather-edged skewNo.42UNDEFfeather-edged skew